Leading 10 common forklift accidents ， forklift procedure should take note of these matters ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious crashes in mins, and there are several accidents including forklifts.

Situation 1: The forklift cargo obstructed the vehicle driver's view, and the person in front might not be discovered, leading to a rolling mishap.
Situation 2: In order to preserve the balance of the forklift when lifting hefty goods, the workers used their body weight as the weight, which virtually created casualties.
Case 3: The size of the forklift freight exceeds the allowed width of the course and hangs on the roadside rack, which nearly triggers an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Instance 5: The forklift chauffeur did not see the pedestrian, and the pedestrian did not discover the forklift.
Situation 6: The forklift raises the workers unlawfully, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Situation 7: The forklift driver did not wear a seat belt and fell from the automobile when it surrendered and was crushed.
Forklift operation must take note of these issues ：.

Beginning.
1. Prior to starting, observe the surroundings, and after validating that there are no challenges that hinder the security of driving, beep the horn first and afterwards start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a lots, the vehicle driver ought to first confirm that the tons is secure and trusted.
4. The start should be slow-moving and steady.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole must be tilted in reverse. .
2. Do not raise the fork too expensive when driving. When going into and leaving the work site or while driving, be careful that there will be no obstacles overhead. When the lots is taking a trip, the fork has to not be raised expensive, which will certainly affect the security of the forklift. .
3. After unloading, the fork must be decreased to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal needs to be released first. High-speed doglegs are prohibited. High-speed doglegs will cause the car to lose lateral security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to turn off the flame and slide, and it is prohibited to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it needs to obey the web traffic rules in the factory and should maintain a certain safety and security range from the vehicle ahead. .
7. When the forklift is running, the lots needs to be in the most affordable setting that does not hinder the driving, and the gantry ought to be correctly tilted back. The tons will not be elevated except when stacking or loading. .
8. The height of the load need to not obstruct the motorist's view. In unique circumstances, when the thing influences the forward vision, drive at a low speed when turning around.
9. It is restricted to turn on the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility area is 5 km/h, and it must drive securely at a low rate when getting in the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is prohibited for workers to depend on the fork to hold products and play a stabilizing role. .
12. If issues are located, they will be fixed and reported in a timely manner, and they will never ever operate with diseases or hide them.

packing and dumping.
1. When fork-loading things, the range in between both forks must be changed as required to make the tons of both forks balanced and not manipulated, and one side of the product ought to protest the shelf. .
2. It is restricted to work with a solitary fork or utilize a fork top or pull. In special situations, security warning signs must be established to advise surrounding pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The speed of the vehicle must be sluggish and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When using a fork to fork the goods, the fork should be as deep as feasible under the lots, and it ought to be noted that the fork pointer should not touch various other goods or items. The load should be supported with marginal back tilt of the gantry to ensure that the load does not glide in reverse. The mast can be slanted ahead slightly when the lots is reduced to permit easy positioning of the lots and extraction of the forks. .
6. It is prohibited to fork products at broadband and ram tough items with the fork head. .
7. When the forklift is working, it is prohibited for individuals to stand around the fork, so regarding prevent the collapse of the goods and harm individuals. .
8. Overwhelming is banned, and it is banned to utilize forks to lift workers to take part in high-altitude operations to prevent high-altitude dropping mishaps. .
9. It is not permitted to use the brake inertia to slip, place, round or roll objects. .
10. It is not enabled to utilize forks to pick, turn pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork are in the air. Before leaving the forklift, you must discharge the goods or reduced the fork structure.
2. Pull the parking brake handle to dead or dispirit the emergency brake button.
3. The engine is switched off and the power is cut off. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look must be checked, and gas, lubricating oil and air conditioning water need to be added.
2. Examine the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are full and effective.
4. Throughout the operation of the forklift, check Stand-on Electric Pallet Stacker whether the stress and temperature are typical.
5. After the forklift is running, the outside leak needs to also be checked and the seals should be replaced in time.

Forklift Safety Operation Specifications.
1. You must inspect prior to leaving the cars and truck;.
2. When you encounter someone in front of you throughout driving, you should send a signal at a distance of 5 m;.
3. The driving speed in the factory does not surpass 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming need to not be also sharp to stop the tendency of " complimentary switching";.
6. Adding and down the slope must be sluggish and uniform, and no activating the slope is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the automobile should be driven backwards when declining;.
8. When the forklift workers lug the goods and move forward, if they run into big Stand-on Electric Pallet Stacker or heavy products and most likely to the vehicle driver's line of sight, they need to take the turning around workout
.
The "Eight Prohibitions" ought to be complied with in the operation.
1. Solitary fork procedure is not allowed.
2. It is not allowed to lift the goods for cross country driving.
3. It is not enabled to get the goods by turning over the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not permitted to utilize inertia pressure to get the goods.
6. It is not permitted to utilize stopping pressure to expatriation round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on slopes
.
Parking is not allowed under the list below conditions.
1. Curves, slim roads, railway crossings;.
2. Areas with a longitudinal incline higher than 5%.
3. When there is an obstacle on one side of the roadway, the contrary side of the section with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844